Electronic Ruler, Angle Measurement Displacement Angle to Modbus Module 3-Wire Potentiometer Input

• Customization: Available
• Product Features: Resistance Potentiometer Electronic Ruler Signal a
• Product Features1: Using a 12 Bitad Converter, The Measurement Accura
• Model NO.: WJ123
• Product Features2: The Accuracy of The Calibration Module Can Be Prog
• Product Features3: High Reliability, Easy Programming, and Easy Appli
• Product Features4: Users Can Program Module Addresses, Baud Rates, Et
• Typical Applications: Potentiometer, Displacement Signal Measurement
• Typical Applications2: RS-485 Remote I/O, Data Acquisition
• Temperature Drift: ± 50 Ppm/℃ (± 100 Ppm/℃, Maximum)
• Input Impedance: Greater Than 1m ω
• Bandwidth: -3 dB 10 Hz
• Input Protection: Overvoltage Protection, Overcurrent Protection
• Transport Package: Wayjunr
• Specification: 79x69.5x25mm
• Trademark: wayjunr
• Origin: Guangdong, China
• Production Capacity: 9999
• Package Size: 20.00cm * 20.00cm * 20.00cm
• Package Gross Weight: 0.200kg

Product Description

 Resistance potentiometer electronic ruler to RS-485, displacement angle to Modbus
 module WJ123

 Product features:
 Resistance potentiometer electronic ruler signal acquisition and conversion to RS-485 output
 Using a 12 bitAD converter, the measurement accuracy is better than 0.1%
 The accuracy of the calibration module can be programmed through the RS-485 interface
 Isolation withstand voltage between signal input/output 1000VDC
 Wide power supply range: 8~32VDC
 High reliability, easy programming, and easy application
 Standard DIN35 rail installation, convenient for centralized wiring
 Users can program module addresses, baud rates, etc
 Supports Modbus RTU communication protocol and automatic recognition protocol
 Industrial flame retardant shell, RS485 port surge protection
 The ADconversion rate can be programmed and set
 Typical applications:
 Potentiometer, displacement signal measurement
 RS-485 remote I/O, data acquisition
 Electronic ruler, angle measurement, etc
 RS-485 bus industrial automation control system
module appearance diagram
 Industrial site signal isolation and long-distance transmission
 Equipment operation monitoring
 Measurement of sensor signals
 Acquisition and recording of industrial field data
 Development of medical and industrial control products

Product selection:  WJ123- R- 485
	Input resistance signal value communication interface
	The supported	four  Output as RS-485
Note: It must be a 3-wire potentiometer input, and for 2-wire resistance measurement, please use the WJ121 series.  Selection example: Model: WJ123-R-485 represents the potentiometer signal input with a resistance range of 100  Ω~500K Ω, and the output is RS-485 interface

Company Profile

Shenzhen Weijunrui Technology Co., Ltd

Since: 2011
Specialty: The company's main products include analog acquisition modules, signal isolators/conversion modules, and signal transmitters
Capacity: Produce 10000 per month
Advanced Features:
Switching to TCP/network/remote IO module, Modbus RTU to TCP, RS232/485 to Ethernet, analog signal (current/voltage/thermistor/frequency/displacement/speed/pulse) isolation transmitter, mV differential signal amplifier, isolation amplifier, micro power DC-DC module power supply, etc

 WJ123 General Parameters:

Function Introduction:

 (Typical @+25 ℃, Vs is 24VDC)
 Input type: Three wire potentiometer resistor input, with a resistance range of 100 Ω~500K Ω.
 Accuracy: 0.1%
 Temperature drift: ± 50 ppm/℃ (± 100 ppm/℃, maximum)
 Input impedance: greater than 1M Ω
 Bandwidth:-3 dB 10 Hz
 Conversion rate: 10Sps (factory default value, users can modify the conversion rate by issuing commands.)
 You can set the AD conversion rate to 2.5 SPS, 5 SPS, 10 SPS, and 20 SPS by sending commands.
 Note: Please recalibrate the module after modifying the conversion rate, otherwise the measured data may have
 deviations. You can also specify the conversion rate when placing an order, and we will
 recalibrate the product according to the conversion rate you require when it leaves the factory.
 Common moderejection (CMR): 120 dB (1k Ω Source Imbalance @ 50/60 Hz)
 Normal mode suppression (NMR): 60 dB (1k Ω Source Imbalance @ 50/60 Hz)
 Input protection: overvoltage protection, overcurrent protection
 Communication: RS-485 standard character protocol and MODBUS RTU communication protocol
 Baud rates (2400, 4800, 9600, 19200, 38400, 57600, 115200bps) can be selected by software
 The address (0-255) can be selected by software
 Communication response time: 100 ms maximum
 Working power supply:+8~32VDC wide power supply range, with internal anti reverse and overvoltage protection
 circuits
 Power consumption: less than 1W
 Working temperature:-45~+80 ℃
 Working humidity: 10~90% (no condensation)
 Storage temperature:-45~+80 ℃
 Storage humidity: 10~95% (no condensation)
 Isolation withstand voltage: 1KVDC between input/output, 1 minute, leakage current 1mA
 The RS-485 output and power supply are grounded together.
 Surge resistant voltage: 1KVAC, 1.2/50us (peak value)
 Dimensions: 106 mm x 59mm x 24mm

 The WJ123 signal isolation acquisition module can be used to measure the resistance signal of a three wire
 potentiometer.
 1,Potentiometer signal input
 12 bit acquisition accuracy, potentiometer resistance signal input. The product has been fully calibrated before
 leaving the factory. Users do not need to calibrate.
 2,Communication Protocol
 Communication interface: 1 standard RS-485 communication interface.
 Communication Protocol: Supports two protocols, the character protocol defined by the command set and the
 MODBUSRTUcommunication protocol. The module automatically recognizes communication
 protocols and can achieve network communication with various brands of PLCs, RTUs, or computer
 monitoring systems.
 Data format: 10 digits. 1 start bit, 8 data bits, 1 stop bit, no checksum.
 The communication address (0-255) and baud rate (2400, 4800, 9600, 19200, 38400, 57600, 115200bps) can be set;
 The communication network can reach a maximum distance of 1200 meters and is connected through
 twisted pair shielded cables.
 High anti-interference design of communication interface, ± 15KV ESD protection, communication response time
 less than 100mS.
 3,anti-interference
 Checksums can be set as needed. There is a transient suppression diode inside the module, which can effectively
 suppress various surge pulses, protect the module, and the internal digital filter can also effectively suppress power
 frequency interference from the power grid

FAQ

Q: How to contact you?
A: Please contact us via email or online customer service